Struct Dr6

pub struct Dr6 { /* private fields */ }

Debug register 6 (dr6) flags.

Implementations

impl Dr6

pub const B0: Self

B0 breakpoint condition detected

Notes

The flag is set if the condition described for the breakpoint by the LENn, and R/Wn flags in debug control register DR7 is true. They may or may not be set if the breakpoint is not enabled by the Ln or the Gn flags in register DR7. Therefore on a #DB, a debug handler should check only those B0-B3 bits which correspond to an enabled breakpoint.

pub const B1: Self

B1 breakpoint condition detected

Notes

The flag is set if the condition described for the breakpoint by the LENn, and R/Wn flags in debug control register DR7 is true. They may or may not be set if the breakpoint is not enabled by the Ln or the Gn flags in register DR7. Therefore on a #DB, a debug handler should check only those B0-B3 bits which correspond to an enabled breakpoint.

pub const B2: Self

B2 breakpoint condition detected

Notes

The flag is set if the condition described for the breakpoint by the LENn, and R/Wn flags in debug control register DR7 is true. They may or may not be set if the breakpoint is not enabled by the Ln or the Gn flags in register DR7. Therefore on a #DB, a debug handler should check only those B0-B3 bits which correspond to an enabled breakpoint.

pub const B3: Self

B3 breakpoint condition detected

Notes

The flag is set if the condition described for the breakpoint by the LENn, and R/Wn flags in debug control register DR7 is true. They may or may not be set if the breakpoint is not enabled by the Ln or the Gn flags in register DR7. Therefore on a #DB, a debug handler should check only those B0-B3 bits which correspond to an enabled breakpoint.

pub const BD: Self

BD debug register access detected

Indicates that the next instruction in the instruction stream accesses one of the debug registers.

This flag is enabled when the GD (general detect) flag in debug control register DR7 is set.

pub const BS: Self

BS single step

Indicates (when set) that the debug exception was triggered by the single- step execution mode (enabled with the TF flag in the EFLAGS register).

pub const BT: Self

BT task switch

Indicates (when set) that the debug exception resulted from a task switch where the T flag (debug trap flag) in the TSS of the target task was set.

pub const RTM: Self

Enables (when set) advanced debugging of RTM transactional regions.

pub const fn empty() -> Self

Returns an empty set of flags.

pub const fn all() -> Self

Returns the set containing all flags.

pub const fn bits(&self) -> usize

Returns the raw value of the flags currently stored.

pub const fn from_bits(bits: usize) -> Option<Self>

Convert from underlying bit representation, unless that representation contains bits that do not correspond to a flag.

pub const fn from_bits_truncate(bits: usize) -> Self

Convert from underlying bit representation, dropping any bits that do not correspond to flags.

pub const unsafe fn from_bits_unchecked(bits: usize) -> Self

Convert from underlying bit representation, preserving all bits (even those not corresponding to a defined flag).

Safety

The caller of the bitflags! macro can chose to allow or disallow extra bits for their bitflags type.

The caller of from_bits_unchecked() has to ensure that all bits correspond to a defined flag or that extra bits are valid for this bitflags type.

pub const fn is_empty(&self) -> bool

Returns true if no flags are currently stored.

pub const fn is_all(&self) -> bool

Returns true if all flags are currently set.

pub const fn intersects(&self, other: Self) -> bool

Returns true if there are flags common to both self and other.

pub const fn contains(&self, other: Self) -> bool

Returns true if all of the flags in other are contained within self.

pub fn insert(&mut self, other: Self)

Inserts the specified flags in-place.

pub fn remove(&mut self, other: Self)

Removes the specified flags in-place.

pub fn toggle(&mut self, other: Self)

Toggles the specified flags in-place.

pub fn set(&mut self, other: Self, value: bool)

Inserts or removes the specified flags depending on the passed value.

pub const fn intersection(self, other: Self) -> Self

Returns the intersection between the flags in self and other.

Specifically, the returned set contains only the flags which are present in both self and other.

This is equivalent to using the & operator (e.g. ops::BitAnd), as in flags & other.

pub const fn union(self, other: Self) -> Self

Returns the union of between the flags in self and other.

Specifically, the returned set contains all flags which are present in either self or other, including any which are present in both (see Self::symmetric_difference if that is undesirable).

This is equivalent to using the | operator (e.g. ops::BitOr), as in flags | other.

pub const fn difference(self, other: Self) -> Self

Returns the difference between the flags in self and other.

Specifically, the returned set contains all flags present in self, except for the ones present in other.

It is also conceptually equivalent to the “bit-clear” operation: flags & !other (and this syntax is also supported).

This is equivalent to using the - operator (e.g. ops::Sub), as in flags - other.

pub const fn symmetric_difference(self, other: Self) -> Self

Returns the symmetric difference between the flags in self and other.

Specifically, the returned set contains the flags present which are present in self or other, but that are not present in both. Equivalently, it contains the flags present in exactly one of the sets self and other.

This is equivalent to using the ^ operator (e.g. ops::BitXor), as in flags ^ other.

pub const fn complement(self) -> Self

Returns the complement of this set of flags.

Specifically, the returned set contains all the flags which are not set in self, but which are allowed for this type.

Alternatively, it can be thought of as the set difference between Self::all() and self (e.g. Self::all() - self)

This is equivalent to using the ! operator (e.g. ops::Not), as in !flags.

Trait Implementations

impl Binary for Dr6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl BitAnd for Dr6

fn bitand(self, other: Self) -> Self

Returns the intersection between the two sets of flags.

type Output = Dr6

The resulting type after applying the & operator.

impl BitAndAssign for Dr6

fn bitand_assign(&mut self, other: Self)

Disables all flags disabled in the set.

impl BitOr for Dr6

fn bitor(self, other: Dr6) -> Self

Returns the union of the two sets of flags.

type Output = Dr6

The resulting type after applying the | operator.

impl BitOrAssign for Dr6

fn bitor_assign(&mut self, other: Self)

Adds the set of flags.

impl BitXor for Dr6

fn bitxor(self, other: Self) -> Self

Returns the left flags, but with all the right flags toggled.

type Output = Dr6

The resulting type after applying the ^ operator.

impl BitXorAssign for Dr6

fn bitxor_assign(&mut self, other: Self)

Toggles the set of flags.

impl Clone for Dr6

fn clone(&self) -> Dr6

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Dr6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Extend<Dr6> for Dr6

fn extend<T: IntoIterator<Item = Self>>(&mut self, iterator: T)

Extends a collection with the contents of an iterator.

fn extend_one(&mut self, item: A)

🔬This is a nightly-only experimental API. (extend_one)

Extends a collection with exactly one element.

fn extend_reserve(&mut self, additional: usize)

🔬This is a nightly-only experimental API. (extend_one)

Reserves capacity in a collection for the given number of additional elements.

impl FromIterator<Dr6> for Dr6

fn from_iter<T: IntoIterator<Item = Self>>(iterator: T) -> Self

Creates a value from an iterator.

impl Hash for Dr6

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl LowerHex for Dr6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Not for Dr6

fn not(self) -> Self

Returns the complement of this set of flags.

type Output = Dr6

The resulting type after applying the ! operator.

impl Octal for Dr6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Ord for Dr6

fn cmp(&self, other: &Dr6) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

impl PartialEq for Dr6

fn eq(&self, other: &Dr6) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl PartialOrd for Dr6

fn partial_cmp(&self, other: &Dr6) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl Sub for Dr6

fn sub(self, other: Self) -> Self

Returns the set difference of the two sets of flags.

type Output = Dr6

The resulting type after applying the - operator.

impl SubAssign for Dr6

fn sub_assign(&mut self, other: Self)

Disables all flags enabled in the set.

impl UpperHex for Dr6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Copy for Dr6

impl Eq for Dr6

impl StructuralPartialEq for Dr6